The Leaky Faucet

There are a great deal of projects we hope to get finished in our yard this summer.  Many of them require having water. (cleaning gutters, planting grass, etc.)  Unfortunately, our existing water faucet leaked heavily anytime we turned it on.  We were worried about so much water pooling so close to the foundation.  This made fixing the water spigot a top priority.

IMG_2356

Water sprayed from two places whenever water flowed.  It leaked from the handle and also from the hose bib vacuum breaker (where the hose attaches)

I was able to fix one of the leaks by tightening the packing nut just beneath the handle.  That was fairly simple.  However, the other leak was more complicated because it would have required a part I could not find at either Home Depot or Menards.  The rubber seal inside the vacuum breaker was completely shot.  (photo below)

IMG_2362

The seal on the hose bib vacuum breaker was shot. This meant water would spray through small holes in this device anytime the water was turned on.

I had trouble finding a replacement because the thread on this is 1″ in diameter.  Most typically come with a 3/4″ thread (click for example).  People I spoke with also said I would have a hard time finding a replacement rubber seal.  So after much frustration, and many weeks weighing my options, I decided to replace the entire unit.  It was not going to be as easy as unscrewing the old faucet and fastening a new one.  I would have to learn how to cut brass and solder a replacement.  I was lucky enough to have a shutoff valve just inside the house so that in the event that I needed to call for professional help, we could continue flushing toilets while we waited.

IMG_2359

The shutoff valve for the faucet is about 2 feet away from the exterior wall leaving me plenty of space to work

To learn some DIY plumbing skills, I enlisted the help of my Dad.  Over the course of my lifetime, he has remodeled every room of their home, which was built in 1889.  We happened to be visiting them in Iowa and spent some time learning how to cut and solder brass.

photo 1(1)

He taught me to use a propane torch to heat the brass until it starts to change color

photo 2(1)

He also taught me to clean the brass and prepare it using flux, which sucks the solder into place for a tight seal

See what I learned about applying soldering in the following video:

 

After giving me the “mental” tools to do the job, my dad also sent me home with some of the physical tools I would need (brush, flux, pipe cutter).  After arriving back in Minnesota, we didn’t waste much time getting to work.

10404889_10100677844970423_1996091198308192192_n

Old water faucet removed by cutting brass pipe on the inside of the house (water shutoff valve safely closed)

10173782_10100677845214933_6213606845951662587_n

The pipe is secured in my vise so I can remove the old faucet and reuse the brass pipe

10308270_10100677845299763_2226543513102828889_n

Fire it up!

10410545_10100677845384593_6162611373882637452_n

Heating the pipe to melt the old solder so I can remove the leaky faucet

10172730_10100677845459443_6886273242934779014_n

What the old faucet looks like

We had replacement parts standing by.  In the series of photos below, you will see how I am using a different strategy mounting the new faucet to the pipe.  Instead of soldering it directly to the brass pipe, I am attaching a thread to the pipe, so I have the option in the future of replacing the faucet head if it leaks in the future.

10356251_10100677845659043_8468390790855337545_n

A new brass sillcock and several fittings to attach everything together.  You also see a part of our banister sitting on the workbench (stay tuned for exciting future post!)

As I learned from my dad, I prepared each pipe I would be soldering by brushing it down, then applying flux with a small brush.

10346191_10100677845838683_6672496233771430532_n

This pipe needed to be brushed on the outside.  You can see the container of flux just behind it.

10340128_10100677845798763_7808977373858050335_n

The threaded piece that will go over the pipe needed to be brushed from the inside

After applying heat until the metal started to change color, I touched the coil of solder to the brass and the flux sucked it into place.  I have one fitting ready to go!

10369738_10100677845993373_7974592177171258189_n

My first successful soldering job!

After the fittings were soldered into place, I made three revolutions around the threads with plumbers tape (which I later found wasn’t enough) and tightened the sillcock (faucet head) into place.  The nearly-finished product below:

10352780_10100677846357643_5439893439310085396_n

The pipe with attached faucet is ready to be put into place.  It’s had about 30 minutes to cool.

Adding the extra threaded piece made the pipe longer than it used to be.  This meant I would need to shorten the pipe next to the shutoff valve, or have the entire thing stick out of the house about an inch too far.

10401912_10100677846402553_4479258494941792986_n

I used a piece of metal flashing to protect the wood in our basement from the heat of the propane torch.

After the cut is complete, we just need to line up the two ends, make sure the faucet is facing the correct direction on the outside of the house and solder the two pieces together.

10338729_10100677846452453_1313061146502632053_n

All sealed!

10171143_10100677846502353_7746669513377654387_n

Another view of the finished product inside the basement.

10313835_10100677846567223_3130973337760575695_n

As you can see, the previous owners thought that caulk was the only solution.

I waited about a day before sealing around this because I wanted to check for any leaks.  I did have a minor drip from the sillcock, but that was resolved after I applied 5 layers of plumbers tape instead of just 3.

Click here to see the second spigot I fixed.

-Mike